Steps to Unscrew Your Coil Back For a New Battery

vape coil

Steps to Unscrew Your Coil Back For a New Battery

The Vaping World has been abuzz with the hottest new thing in electronic cigarettes, the vape Coil. This product is an upgrade to the standard Coil technology that has been used for years in vaporizers and other similar products. The name Vaping is derived from the actual sound that is produced when the coil is first heated. When it is first heated, it creates a vapor trail that resembles that of burning a traditional cigarette.

The reason the Vaping World has been so excited about the Vape Coil is because it utilizes the new Wicking Material. The new material is much more pliable than the typical wire. It also has a much tighter coil wire so there are less relapsing leaks. The biggest improvement over the traditional wire is the tight coils. This is the main reason why so many papers are switching from the standard wire to the new.

To replace your old coil you will need the following tools: A razor knife, a hacksaw, a nut puller, pliers and a pair of wire cutters. The idea is to unscrew the old coil and replace it with the new one. There are usually two screws that attach the base to the machine as well.

Once you have all of the above items, the first step is to put the new Vaporizer or Juice Extractor into the tank of the E-juice. Once this is done then you are ready to start replacing the old coil with the new one. To do this you will need to take apart one end of the original tapered head. You will also need to unscrew the three nuts that are on the top.

Once the nuts are unscrewed, you will need to remove the tapered head from the old coil. You will now need to discard the bottom coil (the one that conducts the electrical resistance) and discard the steel mesh that is connected to the top. Now you will be left with the one piece of metal that acts as the bottom. This is the steel mesh that conducts the Ohms to the bottom. To allow the Ohms to flow this wire has to be removed.

Once this has been done you will want to strip the old flavour from the wires. If you want to add a different flavour you can do this but if you do not you can always start over with the new coil. Once you have added the new coil to the coil base then you can wrap the entire thing in electrical tape. The reason why you are doing this step is to help the Ohms flow properly into the new coil so that you get the best vapor production.

After you have successfully replaced all of the components then you are ready for the final step. That is wrapping the entire kit together so that everything is covered in electrical tape. You will also want to tie the wires from the batteries together.

When everything has been wrapped, you will want to place your new Coil over the top of your previous coil. You will need to make sure that the new coil is above the ground wire. It is a good idea to have the safety tested out. Then you can place your new DIY e-juice kit in your pocket and enjoy the taste.

The last step is to fill your new DIY e-juice kit with water. You can use any type of water but I personally like to use juice or water that is room temperature. After you have filled up your tank, you will want to slowly drizzle some e-juice into the tank. Make sure you use a cotton swab to push the e-juice into the tank. If you do not you can spill your juices all over your counter.

At this point you are now ready to enjoy your new battery chargers. You can find these at any local department store. The one I used worked great and I did not spill a drop of e-juice. The only thing I would change about this device is to get a larger battery so that you can use it longer. If you do not mind spending a few extra dollars then by all means buy a bigger battery. That is the only downside I can think of.

The final steps are probably the most important, putting your Vape Coil Replacement covers back on the unit and screws the battery into place. This is pretty easy if you have screws available. Before I go I want to strongly recommend that if you do not have screws available you use the screwdriver that came with the original unit. The reason I say this, is because if you do not screw them in, the e-liquid tank inside may break and you will be left without a working vaporizer.